manualshive.com logo in svg

Jetter JXM-IO-EW30, User Manual, Page: 19 / 56

Share
Download
Jetter JXM-IO-EW30 User Manual Download Page 19

Jetter AG

Mechanical installation | 5

jxm-io-ew30_ba_2151_manual

19 / 56

5 Mechanical installation

NOTICE

Damages to material or functional impairment

Welding on the chassis may cause damages to material of the device, or impair
its functions.

►

Before you start welding, disconnect all connections between the device and
the electric system of the vehicle.

►

Protect the device from flying sparks and welding beads (splatter).

►

Do not touch the device with the welding electrode or earth clamp.

NOTICE

Dirt and moisture can affect the electrical connections.

►

Plug unused pins with blanking plugs.

►

Protect all electrical connections with appropriate single wire seals.

5.1 Requirements for the installation location

Requirements for
the mounting sur-
face

Category

Description

Suitable materials

No special material requirements

Shape / quality

The contact surface must be plane.

Fastening eye

All existing fastening lugs must be screwed down.
The device can directly be fastened to the vehicle or
to a mounting plate.

Tab. 18: 

Requirements for the mounting surface

Requirements for
the screw connec-
tion

Category

Description

Screws/bolts

Diameter 6 mm

Lock washers

Lock washers are recommended to prevent vibration-
induced loosening of the screws

Tightening torque

4 Nm max.

Cable fixation and strain
relief

Mechanical fixation and strain relief of the cables is
necessary to avoid vibration-induced cable breakage
or excessive strain on the connectors

Tab. 19: 

Requirements for the screw connection

Requirements for
the installation
space

■

Sufficient air circulation

■

Sufficient space between the device and parts that may become very hot

■

The device must be accessible for service work at all times.

5.2 Allowed mounting orientations

When installing the JXM-IO-EW30-G27, make sure that the environment of the 5-
pin M12 connector is protected from dust and water as best as possible. Do not
install the unit with the connector facing up. In addition, make sure that the M25
cable gland is firmly tightened to maintain the IP protection class.

 INFO

Clean the area around the 5-pin M12 connector before disconnecting the mating
connector to prevent dust or water from entering.

Summary of Contents for JXM-IO-EW30

























































Reviews:

No comments