janitza UMG 96S Operating Instructions Manual Download Page 7 | Manualshive

Page: 7 / 96

background image

Page 7

Product description

Intended use

The UMG96S has been designed for a fixed in-
stallation in panels, measuring voltage, current,
power etc. in low voltage switchgear. The meas-
urement is laid out for three phase systems with
neutral conductor (TN and TT networks).
The UMG96S gets its operating voltage from the
measuring  voltage  and  can  be  delivered  for
operating voltage of 150V and 300V. The 300V
standard  version,  measurement  and  operation
voltage  (50Hz/60Hz)  up  to  300VAC  against
ground  and  520VAC  phase  to  phase  can  be
connected  directly.  The  150V  special  version,
measurement  and  operating  voltage  (50Hz/
60Hz)  up  to  150VAC  against  ground  and
240VAC phase to phase can be connected di-
rectly.
The measurement and operational voltage must
be connected to the UMG96S via a separation
(circuit breaker or power switch) and a fuse (2-
10A)  within  the  installation.  The  separation
(circuit  breaker  or  power  switch)  must  be  near
to the instrument and easy to reach.
The connection of the measurement and oper-
ating  voltage  is  carried  out  on  the  backside  of
the UMG96S via touch proof spring terminal. To
the  current  inputs,  either  .../5A  or  .../1A  trans-
formers can be connected.

Attention!

Measurement in systems with pulse load
is not possible, because no continuous
scanning of the measuring signals is car-
ried out.

m

Attention!

The inputs, outputs and serial interfaces
must be shielded.

m

Attention!

The connection of the neutral conductor
N is absolutely neccessary.

m

«
...
5
6
7
8
9
...
»

Summary of Contents for UMG 96S

































































































Reviews:

No comments

Related manuals for UMG 96S

Brand: Oakton Pages: 4

Brand: ABQ Industrial Pages: 15

Brand: ABQINDUSTRIAL Pages: 3

Brand: Hach Pages: 145

Brand: Hach Pages: 358

Polymetron 9582sc

Brand: Hach Pages: 280

Brand: HACH LANGE Pages: 15

Brand: Idexx Pages: 6

Brand: IDEAL INDUSTRIES Pages: 10

Brand: M-system Pages: 5

Brand: Olympus Pages: 362

Brand: Olympus Pages: 8

Brand: Qu-Bit Electronix Pages: 10

Brand: Vaisala Pages: 2

Brand: E Instruments Pages: 144

Brand: Det-Tronics Pages: 18

Brand: OHAUS Pages: 84

Brand: PCE Health and Fitness Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands