manualshive.com logo in svg

janitza UMG 96S, Operating Instructions Manual, Page: 56 / 96

Share
Download
janitza UMG 96S Operating Instructions Manual Download Page 56

Page 56

Profibus profiles

There are many measured values available for
transmission. To keep the data to be transmitted
via Profibus small in number, only a selection of
the possible measured data will be transmitted
by UMG96S. The selected measured values are
combined  in  16  different  profiles.  The
programming  of  specific  data  is  not  possible.
The  profiles  have  the  description  of  profile
number 1 to 16.
If  a  certain  profile  is  required  by  the  Profibus
master, please write the desired profile number
into the first Byte of the output range of the PLC.
The  UMG96S  supplies  the  input  range  of  the
PLC  with  the  first  2  Bytes  of  the  actual  profile
number and the condition of the three compara-
tors.
If  not  all  values  of  the  selected  profile  are
needed, you can pick the first measured values
from a profile only.
Via the 2nd Byte of the output range of the PLC,
the two outputs of the UMG96S can be
activated. The relation is:
Output 1 = Input/Output 1 = Terminal 12
Output 2 = Input/Output 2 = Terminal 13

Profile formats

The  measured  values  can  be  retrieved  in  14
profiles in integer and floating point format. Ad-
ditionally, the formats "high before low byte" or
"low  before  high  byte"  can  be  provided.  Meas-
ured  values  in  integer  format  do  not  contain
current and voltage transformer ratios.

Diagr. Data transmission PLC - UMG96S.

UMG96S

 Input range of the PLC

1. Byte Back signal of profile number
2. Byte Condition of comparators

Format:
2 x 3 Conditions of comparators.
Condition of two digital inputs.

3. Byte Contents of the selected profile.
..

..

..

..

124. Byte

Output range of the PLC

1. Byte

Profile number.

2. Byte Bit 0

Set Output 1.

Bit 1

Set output 2.
0= off = Transistor blocked.
1= on = Transistor active.

SPS

 Profibus profile No.

Format

 1..14 + 128

Integer format

 1..14 + 31 + 128

Float formats (4Byte)

Table: Measured values "high before low byte"

 Profibus profile No.

Format

 1..14

Integer format

 1..14 + 31

Float formats (4Byte)

Table: Measured values "low before high byte"

Summary of Contents for UMG 96S

































































































Reviews:

No comments