JAI LQ-401CL User Manual Download Page 68 | Manualshive

Page: 68 / 74

background image

LQ-401CL

67

11. Specifications

11.1 Typical data

Scanning system

Line Scan

Image Sensor

Effective pixels : 4096 pixels
Pixel Size : 7.0 μm × 7.0 μm
Effective image length : 28.672 mm

Pixel clock

84.00 MHz

Line Rate

Full

resolution

/Binning

Total number of pixels per line: 4602 clocks

Line rate: 54.79 μs (No-shutter mode with internal trigger)
Line Frequency:

18.25 kHz

Sub-

sampling

/Windowing

Total number of pixels per line: 2554 clocks
Line rate: 30.40 μs (No-shutter mode with internal trigger)
Line Frequency:

32.89 kHz

Sensor sensitivity

64nJ/cm

2

Sensitivity

(Standard)

RGB : 2800 Lx ( 7800K White LED light)

Conditions: Line Rate=600

μ

s, Gain=0dB, Shutter=OFF, Lens

iris=F2, 100% output)

NIR : 2.35

μ

W/cm

2

at 800nm

S/N

55 dB (Green channel, Gain=0dB

）

Synchronization

Internal

Video output

Digital 8-Bit x 4 or 10-Bit x 4 (Camera Link)
* Default setting: 8-bit
* Built-in pre emphasis function makes 10m transmission possible

Gain range

Mode select:
      Master mode : Adjust master level and match R,G,B and NIR
                                  Master(Green): 0dB to +8dB
                                  R/B/NIR : -4dB to +6dB
      Individual      : Adjust each channel individually
                                R/G/B/NIR : -4dB to +14dB
* Default setting: Master mode

White balance

Adjustable range : 4000K to 9000K
Standard color temperature : 7800K

Black level

(User setup)

Mode select:
      Master mode : Adjust master level and match R,G,B and NIR
                                  Master(Green): 0 to 64 LSB(10-bit output)
                                  R/B/NIR : -64 to 63 LSB (10-bit output)
      Individual      : Adjust each channel individually
                                R/G/B/NIR : 0 to 64 LSB (10-bit output)
* Default setting: Master mode 8-bit (8 LSB)

Line rate

(Variable) (Note1)

Range : 54.79

μ

s (1L) to 14.30 ms (SensReadout is OFF)

30.40 μs (1L) to 7.11 ms (SensReadout is subsampling

/Windowing)

Adjustment increment : 11.9 ns (1clk)

This mode is available for No-shutter internal trigger and Shutter-
Select internal trigger modes.

Electronic shutter

Available for Shutter-Select mode
Adjustable range : 9.52 μs to 14.20 ms
Adjustment increments : 11.9 ns (1 clk)

«
...
66
67
68
69
70
...
»

Summary of Contents for LQ-401CL











































































Reviews:

No comments

Related manuals for LQ-401CL

Brand: Cam Scan Pages: 7

Brand: MagicRadar Pages: 98

Zuiko Digital ED 9-18mm f4.0-5.6

Brand: Olympus Pages: 2

ZUIKO DIGITAL ED 70-300mm F4.0-5.6

Brand: Olympus Pages: 2

Zuiko digital ED 50-200mm f2.8-3.5 SWD

Brand: Olympus Pages: 2

Lens 14-54mm f2.8-3.5 Zuiko Digital

Brand: Olympus Pages: 2

Brand: Ubiquiti Pages: 31

Brand: Q-See Pages: 1

Brand: IDS Pages: 8

XRX300 LED Series

Brand: WE-EF Pages: 6

Brand: MeiTrack Pages: 8

Brand: Axis Pages: 30

Brand: nedis Pages: 40

HDW2831TM-AS-S2

Brand: Dahua Technology Pages: 17

Virtuoso Series

Brand: Vitek Pages: 20

Enforcer SM-407-5T

Brand: SECO-LARM Pages: 1

ZUIKO DIGITAL ED50mm f2.0 MACRO

Brand: Olympus Pages: 2

Brand: Chuango Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands