JAI LQ-401CL User Manual Download Page 39

Page: 39 / 74

LQ-401CL

Note: EEN uses channel with the largest exposure value

Fig.43 Shutter-Select /Sub-sampling and Window/ External

6.3.6 Pulse Width Control (PWC) mode

In this mode, the exposure time and readout are activated by the external trigger pulse. The
exposure time depends on the pulse width provided.

To use this mode:
Set function

Trigger mode, PWC

TR=2

Important Note:



The minimum trigger interval

Scan mode

Trigger input via

Minimum interval (

Full/Binning

Camera link

Exposure time + 52.6

12-pin

Exposure time + 57.1

Sub-sampling/windowing

Camera link

Exposure time + 30.4

12-pin

Exposure time + 34.9



The minimum trigger pulse width

Trigger input via

Minimum trigger pulse width

Camera link

52.6 µs

12-pin

57.1 µs



One-push white balance by gain setting only.



When the one-push white balance has been initiated and the rear panel LED shows orange, the

camera must receive continuous external trigger pulses corresponding to the frequency and

duty cycle used in the application.

156clk

EEN

* Note

Exposure R

Exposure G

Exposure B

Exposure NIR

610clk

LVAL

16clk

2048clk

16clk

DVAL

Data

AP0

AP2047

Summary of Contents for LQ-401CL











































































Search results

Summary of Contents for LQ-401CL

Reviews:

Related manuals for LQ-401CL

Brands by name

Popular brands

JAI LQ-401CL, User Manual

Search results

Summary of Contents for LQ-401CL

Reviews:

Related manuals for LQ-401CL

Brands by name

Popular brands