JAI AB-201CL User Manual Download | Manualshive

Page: 45 / 68

background image

AM-201CL / AB-201CL

- 43 -

8.10. Bayer color interpolation (Command : BCIC) (Only for AB-201CL)

This function is available only for AB-201CL. The AB-201CL uses a CCD with an RGB Bayer
pattern. If the Bayer color interpolation is not used, the following RAW data can be
output.

Gｒ

R

Gｒ

R

B

Gb

B

Gb

Gｒ

R

Gｒ

R

Gｒ

R

B

Gb

Gｒ

R

B

Gb

B

Gb

B

Gb

B

Gb

Gｒ

R

B

Gb

Gｒ

R

B

Gb

Gｒ

R

B

Gb

Gｒ

R

Fig.44 Bayer pattern

The  RAW  data  contains  only  luminance  information  for  each  color  and  outputs  as  a
monochrome  signal.  The  Bayer  color  interpolation  can  complement  lacking  color
information  on  each  pixel  and  output  RGB  color  data  as  the  result.  Color  interpolation
compensates for the lack of color information by using information from adjacent pixels.
The following is the concept drawing for the color interpolation process.

G

ｒ

B3

Gb2

B4

B1

Gb1

B2

G

ｒ

1

R

G

ｒ

2

Gb3

B2

Gb4

Gb1

B1

Gb2

R1

G

ｒ

R2

R3

G

ｒ

2

R4

R1

G

ｒ

1

R2

Gb1

B

Gb2

Fig.45 Color interpolation concept drawing

8.11. Test pattern (Command: TPN)

TPN=0

：

Test pattern off

TPN=1

：

AM-800:Black-Wihte AB-800: Color bar

TPN=2

Gray Pattern1

TPN=3

: Gray Pattern2

TPN=4

: white

（

100

％）

Fig.46 Test pattern

«
...
43
44
45
46
47
...
»

Summary of Contents for AB-201CL





































































Reviews:

No comments

Related manuals for AB-201CL

EOS C300 Mark II

Brand: Canon Pages: 16

AWHE100N - HD INTEGRATED CAMERA

Brand: Panasonic Pages: 42

Brand: HANNspree Pages: 13

Brand: Z-CAM Pages: 5

Brand: Ricoh Pages: 160

Brand: Concord Camera Pages: 59

Brand: LEXIBOOK Pages: 37

Brand: Advent Pages: 20

Brand: Nikon Pages: 53

Brand: Panasonic Pages: 1

Brand: Panasonic Pages: 78

Brand: Panasonic Pages: 79

Brand: Panasonic Pages: 104

DMC-LS70S - Lumix Digital Camera

Brand: Panasonic Pages: 120

DMC-L1K - Lumix Digital Camera SLR

Brand: Panasonic Pages: 136

Brand: Panasonic Pages: 420

Brand: Nikon Pages: 157

Brand: Samsung Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands