JAI AB-201CL Page 42 User Manual Download | Manualshive

Page: 42 / 68

background image

AM-201CL / AB-201CL

- 40 -

A

B

C

D

To Camera Link I/F

Tap A

Tap B

TapC

TapD

Note: If 1 tap output is used, the following readout is applied.

Fig.38 Tap control

8.4. Exposure auto (Related Commands : ASC=1(ON), ASCS, ASCEA, ASCEI)

The exposure can be automatically controlled by setting the command ASC to ON.
The adjusting range is 15.56ms to 10

μ

s. The tracking speed can also be set.

Command

Value

Adjusting range

ASCEA, ASCEI

10

μ

s to 15.56ms

Tracking speed

ASCS

1 to 16 (Default:8)

                          ASCEA: Sets the maximum exposure in the ASC mode
                          ASCEI: Sets the minimum exposure in the ASC mode
                          Note: This function works only in Continuous mode or Pre-dump mode.

8.5. Auto white balance (Related commands:AWB, PGS, PGR, PGGR, PGGB, PGB)

In this function, the gain of each R, Gr, Gb and B color can be individually adjusted to get
the proper white balance.

B3

Gb2

B4

B1

Gb1

B2

Gｒ1

R

Gｒ2

Fig. 39 Auto white balance

To adjust white balance, the AB-201CL has three methods: manual adjustment, one-push
auto white balance, and continuous auto white balance.

AWB: 0    OFF (Manual adjustment)
          1    Once (One-push auto white balance)
          2    Continuous (always tracking)

This function can be used with full resolution readout, as well as with AOI readout.
This does not work in trigger mode.

A

B

To Camera Link I/F

Tap A

Tap B

«
...
40
41
42
43
44
...
»

Summary of Contents for AB-201CL





































































Reviews:

No comments

Related manuals for AB-201CL

Brand: Canon Pages: 318

Brand: Canon Pages: 114

Brand: Canon Pages: 36

PowerShot Elph 340 HS IXUS 265 HS

Brand: Canon Pages: 163

PowerShot G1X Mark II

Brand: Canon Pages: 27

Brand: Canon Pages: 2

Brand: Canon Pages: 23

Brand: Canon Pages: 9

Brand: Canon Pages: 8

Brand: Canon Pages: 23

Brand: Canon Pages: 2

POWERSHOT PRO 1

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Canon Pages: 25

Brand: Canon Pages: 6

Brand: Canon Pages: 214

Brand: Canon Pages: 23

Brand: MAGPiX Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands