IVT SNWB-196(4+1), Manual

Page: 11 / 44

11
EN
Instruction manual
distance of the snow leaving the chute. Raising the
angle will increase the throwing distance.
Lowering the angle will decrease the throwing distance.
∙ Make sure the drive control (1) and auger control
(3) are released. The auger (8) has to come to a full
stop.
∙ Loosen the knob on the chute deflector (6) and
adjust the chute deflector (6) to the desired angle.Then
retighten the knob on the chute deflector (6). Do not
over-tighten.
Skid shoes (7) adjustment
The adjustment of the skid shoes (7) governs the
height above the ground at which the auger shave plate
operates.
∙ For clearing snow from concrete, asphalt, and other
smooth surfaces, set the auger shave plate so that the
bottom of the shield scrapes the ground.
∙ For clearing snow from gravel, dirt, and other rough
surfaces to set the auger shave plate slightly above the
ground to avoid dirt and gravel from entering the auger (8).
The optimal height of the shield will vary depending on
the type of surface being cleared. Surfaces with larger
gravel or stones would require a more raised auger
shield plate.
1. Make sure your machine is on a solid, smooth, and
level surface.
2. Place a spacer board on the ground underneath
the auger shave plate between the skid shoes (7). The
thickness of the board should be the same as the height
above the ground you wish to raise the auger shave
plate to. The skid shoes (7) should not touch the board.
3. Using a wrench, loosen the two nuts located on
each skid shoe (7) and allow the skid shoes (7) to slide
to the ground.
4. Re-tighten the nuts on the skid shoes (7) and wheel
your machine off of the spacer board.
Engaging the drive and auger (8) operation
∙ With the throttle control in the Fast ( ) position,
move the shift lever (2) into one of the forward positions
or reverse position. NOTE: When selecting a Drive
Speed, use the slower speeds until you are comfortable
and familiar with the operation of the snow thrower.
∙ Squeeze the auger control (3) against the handle
and the auger (8) will turn. Release it and the auger (8)
will stop.
∙ Squeeze the drive control (1) against the handle
and snow thrower will move. Release it and drive motion
will stop.
Be sure to release both the auger control (3) and the
drive control (1) before adjusting the shift lever (2).
WARNING! Never change the speed
while your machine is moving. It could
damage the drive mechanism and void
the warranty.
Chute Clean-Out Tool (9)
Should snow and ice become clogged in the chute
assembly during operation, proceed as follows to safely
clean the chute assembly and chute opening.
∙ Release both the Auger Control (3) and the Drive
Control (1).
∙ Stop the engine by removing the ignition key.
∙ Take the clean-out tool (9). Use the shovel-shaped
end of the clean-out tool (9) to dislodge and scoop any
snow and ice which has formed in and near the chute
assembly.
∙ Refasten the clean-out tool to the mounting clip on
the rear of the auger housing
∙ Reinsert the ignition key and start the snow
thrower’s engine.
∙ While standing in the operator’s position (behind
the snow thrower), engage the auger control (3) for a
few seconds to clear any remaining snow and ice from
the chute assembly.
SNOW THROWING TIPS
∙ Always operate the machine with the engine at full
throttle. Full throttle offers the best performance.
∙ Go slower in deep, freezing or heavy wet snow.
Use the shift lever (2), not the throttle, to adjust speed.
∙ It is easier and more efficient to remove snow
immediately after it falls.
∙ The best time to remove snow is the early morning.
At this time the snow is usually dry and has not been
exposed to the direct sun and warming temperatures.
∙ Slightly overlap each successive path to ensure all
snow will be removed.
∙ Throw snow downwind whenever possible.
∙ Adjust the skid shoes (7) to proper height for current
snow conditions. For extremely heavy snow, reduce the
width of snow removal by overlapping previous path and
moving slowly.
∙ Keep engine clean and clear of snow during use.
This will help air flow and extend engine life.
WARNING! Do not operate machine if
weather conditions impair visibility.
Throwing snow during a heavy, windy
snowstorm can blind you and be
hazardous to the safe operation of the
machine.