ITT GOULDS PUMPS 3296 EZMAG Installation, Operation And Maintenance Manual Download Page 34

Page: 34 / 100

Check

Explanation/comment

Checked

This helps to prevent misalignment due to linear expansion of
the piping.

Example: Installation for expansion

Correct

Incorrect

This illustration shows a correct installation for expan-
sion:

Expansion loop/joint

This illustration shows an incorrect installation for expan-
sion:

4.5.3 Suction-piping checklist

Performance curve reference

Net positive suction head available (NPSH

) must always exceed NPSH required (NPSH

) as shown on

the published performance curve of the pump.

Refer to the Hydraulic Institute for NPSH and pipe friction values needed in order to evaluate suction pip-
ing.

Suction-piping checks

Check

Explanation/comment

Checked

Flush all suction piping before you connect
it to the pump.

This reduces the risk of pump operation problems.

Check that the suction piping fittings and
joints are airtight and have no leaks.

—

Check that the distance between the inlet
flange of the pump and the closest elbow
is at least two pipe diameters.

This minimizes the risk of cavitation in the suction in-
let of the pump due to turbulence.

See the Example sections for illustrations.

Check that elbows in general do not have
sharp bends.

See the Example sections for illustrations.

—

4.5 Piping checklists

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Summary of Contents for GOULDS PUMPS 3296 EZMAG





































































































Search results

Summary of Contents for GOULDS PUMPS 3296 EZMAG

Reviews:

Related manuals for GOULDS PUMPS 3296 EZMAG

Brands by name

Popular brands

ITT GOULDS PUMPS 3296 EZMAG, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for GOULDS PUMPS 3296 EZMAG

Reviews:

Related manuals for GOULDS PUMPS 3296 EZMAG

Brands by name

Popular brands