ITT GOULDS PUMPS 3296 EZMAG Installation, Operation And Maintenance Manual Download Page 16 | Manualshive

Page: 16 / 100

background image

3 Product Description

3.1 General description

Model 3296 EZMAG

The Model 3296 EZMAG is a sealless centrifugal pump with an enclosed impeller that is driven by a syn-
chronous magnetic coupling. Model 3296 EZMAG meets the dimensional standards of ANSI B73.1.

Casing

The casing is top centerline discharge and is self-venting. It incorporates a fully-confined gasket with AN-
SI Class 150 flanges that are serrated and raised-faced. ANSI Class 300 flanges that are serrated and
raised-face are optional. The 3296 EZMAG is designed to have a metal-to-metal fit between the casing
and the backplate.

Magnetic coupling

The magnetic coupling is a coaxial synchronous type that uses rare earth magnets. This concept results
in a compact design and allows the impeller to turn at the same speed as the motor, which means that
there is no slip between the drive and the driven magnets.

Magnets

Two types of rare earth magnets are available:

•

Neodymium Iron (NdFe) is used when pumped liquid temperatures are less than 180°C | 365°F.

•

Samarium Cobalt (SmCo) is used when pumped liquid temperatures are between 180°C | 365°F
and 280°C | 536°F.

Containment shell

The containment shell isolates the pumped liquid from the atmosphere and is constructed from Hastel-
loy-C.

Sleeve bearings and thrust bearings

Goulds standard bearing material is Pure Sintered Alpha Grade Silicon Carbide. Dryguard

™

bearings are

available for dry-run protection.

Impeller

The 3296 EZMAG uses an enclosed impeller that is hydraulically-balanced and keyed to the shaft.

Bearing frame

The standard configuration is cast iron with ball bearings that are flood oil–lubricated. Greased-for-life
bearings systems are available as an option. Bronze bearing isolators are provided for protection and re-
liability of the bearings and the lubricant.

3.2 Nameplate information

Important information for ordering

Every pump has nameplates that provide information about the pump. The nameplates are located on
the casing and the bearing frame.

3 Product Description

14

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

«
...
14
15
16
17
18
...
»

Summary of Contents for GOULDS PUMPS 3296 EZMAG





































































































Reviews:

No comments

Related manuals for GOULDS PUMPS 3296 EZMAG

Brand: Barnes Pages: 12

Brand: IBO Pages: 22

Brand: DAB Pages: 184

Brand: Wayne Pages: 8

Brand: Carrier Pages: 12

Brand: Stihl Pages: 164

Brand: Esco Pages: 7

Brand: Annovi Reverberi Pages: 14

Brand: GPI Pages: 24

Brand: hajdu Pages: 65

Diamond Products GTXR+

Brand: HydraMaster Pages: 49

Brand: Crivit Pages: 26

Brand: Mega Pages: 40

ThermalFlo Heat Pump Contol Panel Addendum

Brand: Pentair Pages: 16

Elite XP16-024-230

Brand: Lennox Pages: 20

Brand: Rapid Pages: 12

GE50T BQT Series

Brand: GE Pages: 68

GeoSpring GEH50DEEJSC

Brand: GE Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands