ITT GOULDS PUMPS 3296 EZMAG Installation, Operation And Maintenance Manual Download Page 46

Page: 46 / 100

Item Description

Annular groove

End plate (pump end)

Guard half

Figure 22: Annular groove in coupling guard

Use a bolt, a nut, and two washers to secure the coupling guard half to the end plate. Tighten se-
curely.

Item Description

Nut

Washer

Bolt

Figure 23: Secure coupling guard half to end plate

Put the driver half of the coupling guard in place:

a) Slightly spread the bottom apart.

b) Place the driver half of the coupling guard over the pump half of the coupling guard.
The annular groove in the coupling guard half must face the motor.

5.5 Couple the pump and driver

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Summary of Contents for GOULDS PUMPS 3296 EZMAG





































































































Search results

Summary of Contents for GOULDS PUMPS 3296 EZMAG

Reviews:

Related manuals for GOULDS PUMPS 3296 EZMAG

Brands by name

Popular brands

ITT GOULDS PUMPS 3296 EZMAG, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for GOULDS PUMPS 3296 EZMAG

Reviews:

Related manuals for GOULDS PUMPS 3296 EZMAG

Brands by name

Popular brands