ITT GOULDS PUMPS 3296 EZMAG Installation, Operation And Maintenance Manual Download Page 20

Page: 20 / 100

4.1.2 Foundation requirements

Requirements

•

The location and size of the foundation bolt holes must match those shown on the assembly draw-
ing provided with the pump data package.

•

Provide a flat, substantial concrete foundation in order to prevent strain and distortion when you
tighten the foundation bolts.

Sleeve-type bolts

Item Description

Baseplate

Shims

Foundation

Sleeve

Dam

Bolt

Figure 7: Sleeve type bolts

J-type bolts

Item Description

Baseplate

Shims or wedges

Foundation

Dam

Bolt

Figure 8: J-type bolts

4.1 Pre-installation

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Summary of Contents for GOULDS PUMPS 3296 EZMAG





































































































Search results

Summary of Contents for GOULDS PUMPS 3296 EZMAG

Reviews:

Related manuals for GOULDS PUMPS 3296 EZMAG

Brands by name

Popular brands

ITT GOULDS PUMPS 3296 EZMAG, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for GOULDS PUMPS 3296 EZMAG

Reviews:

Related manuals for GOULDS PUMPS 3296 EZMAG

Brands by name

Popular brands