ITT GOULDS PUMPS 3296 EZMAG Installation, Operation And Maintenance Manual Download Page 23

Page: 23 / 100

Item Description

Jackscrew

Baseplate

Foundation

Plate

Figure 11: Jackscrews

Level the driver mounting pads:

NOTICE:

Remove all dirt from the mounting pads in order to ensure that the correct leveling is achieved.
Failure to do so can result in equipment damage or decreased performance.

a) Put one machinist's level lengthwise on one of the two pads.

b) Put the other machinist's level across the ends of the two pads.

Level the pads by adjusting the four jackscrews in the corners.

Make sure that the machinist's level readings are as close to zero as possible, both lengthwise and
across.

Use the baseplate-leveling worksheet when you take the readings.

Item Description

Machinist's levels

Driver's mounting pads

Foundation bolts

Jackscrews

Grout hole

Pump's mounting pads

Figure 12: Level driver mounting pads

4.2 Baseplate-mounting procedures

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Summary of Contents for GOULDS PUMPS 3296 EZMAG





































































































Search results

Summary of Contents for GOULDS PUMPS 3296 EZMAG

Reviews:

Related manuals for GOULDS PUMPS 3296 EZMAG

Brands by name

Popular brands

ITT GOULDS PUMPS 3296 EZMAG, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for GOULDS PUMPS 3296 EZMAG

Reviews:

Related manuals for GOULDS PUMPS 3296 EZMAG

Brands by name

Popular brands