Itel DPRO3 User Manual Download Page 30 | Manualshive

Page: 30 / 59

background image

30

DPRO3 FM Audio Processor

© 2016 ITEL Elettronica e Telecominicazioni Snc

3.2.3

System setup

In this page it is possible to enable and adjust the optional RDS encoder carrier level, the pilot
carrier, insert and adjust the network parameters.

The network parameters are related to the optional network module only. If the streaming module
was installed, network configuration will be done through the web server of the module.

For a detailed description of the following pararmeters, please refer to

MPX output setup

and

RDS Enabled, RDS level, Pilot Level, Pilot Phase, Modulation, Preemphasis, MPX Output Level,
MPX Audio Level
NET IP, NET MASK, NET GATEWAY, NET PORT

Read:

read parameters from the processor

Update:

send changes to the processor

«
...
28
29
30
31
32
...
»

Summary of Contents for DPRO3




























































Reviews:

No comments

Related manuals for DPRO3

Netlink FRX8000

Brand: Cabletron Systems Pages: 94

MMAC-Plus 9E423-24

Brand: Cabletron Systems Pages: 10

MMAC-Plus 9A128-01

Brand: Cabletron Systems Pages: 22

Spectrum EMM-E6

Brand: Cabletron Systems Pages: 2

Brand: Cabletron Systems Pages: 54

Cabletron BRIM-F6

Brand: Cabletron Systems Pages: 43

Netlink FRX4000

Brand: Cabletron Systems Pages: 60

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

Brand: Oracle Pages: 24

Brand: Paradyne Pages: 10

Brand: FDI Pages: 2

Brand: axing Pages: 4

Aquaduct 240 eco

Brand: Aqua Computer Pages: 20

Brand: Rolls Pages: 1

Brand: Echo Pages: 21

Brand: JAKA Pages: 37

H8S/2646 Series

Brand: Renesas Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands