Itel DPRO3 User Manual Download Page 22 | Manualshive

Page: 22 / 59

background image

22

DPRO3 FM Audio Processor

© 2016 ITEL Elettronica e Telecominicazioni Snc

2.6

System setup

2.6.1

Display,Source Dependent Presets, device ID

Contrast:

display contrast adjustment.

Source Dep.Presets:

enable/disable audio preset selection depending on audio source.

ON: if the function is enabled, a different audio processing preset can be specified for each

audio source.

OFF:if the function is disabled, the same preset will be used for all audio sources.

ID:

device identifier. It is a 16 characters long label which will be shown in the main menu screen,

useful for identification when multiple devices are installed.

2.6.2

PassCode Setup

User Password:

in this section the user can enter a numeric password that will be required for

accessing the device. Setting "0000" (default value) will disable the password prompt.

Autologout (mins):

Automatic lock timeout. If no action is done on the front panel knob within the

specified time interval, the device will enter into lock state and the user will need to re-enter the
password to log in again.

LOGOUT:

immediate logout and lock.

SAVE:

Saves any changes made to the numeric password or the duration of the automatic logout

timing.

2.6.3

Ethernet setup

«
...
20
21
22
23
24
...
»

Summary of Contents for DPRO3




























































Reviews:

No comments

Related manuals for DPRO3

UP Squared 6000 Edge Computing Kit

Brand: Aaeon Pages: 59

Brand: Paradyne Pages: 11

Brand: Paradyne Pages: 19

COMSPHERE 3550 Series

Brand: Paradyne Pages: 153

Jetstream CPX-1000

Brand: Paradyne Pages: 141

Brand: Datasat Pages: 170

Brand: Compaq Pages: 112

AIE900-XNX Series

Brand: AXIOMTEK Pages: 53

kontron KBox E-420-R1K/V1K

Brand: S&T Pages: 82

TeleCLIENT TC7730 Series

Brand: ETL Pages: 83

Brand: Idis Pages: 17

Brand: Unex Pages: 27

Brand: JETWAY Pages: 47

Brand: ALIBI Pages: 232

Brand: IBM Pages: 168

Blend PRO BP-2002

Brand: FOLSOM Pages: 89

OPTIMA II CNPS10X

Brand: ZALMAN Pages: 20

Brand: IceManCooler Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands