Itel DPRO3 User Manual Download Page 6

Page: 6 / 59

DPRO3 FM Audio Processor

1.3

Front panel

Front panel indicators and rotary knob

Headphone stereo jack 6,3mm (1/4")

• GATE:

led is on when level is below gate threshold

• CLIP:

the analog input level is too high.

• DIG IN:

AES/EBU digital input is selected as audio source

• NET:

Network audio is selected as audio source(option).

• AGC:

input AGC gain level

• MULTIBAND LIMITER:multiband limiter compression level

Menus navigation and parameter editing is done through the rotary knob.

1.4

Rear panel

Connectors on rear panel

DIG OUT (XLR M)

AES/EBU output

DIG IN (XLR F)

AES/EBU input

LEFT IN (XLR F)

left analog input

RIGHT IN (XLR F)

right analog input

19K OUT (BNC F)

19KHz output for external RDS encoder synchronization. (1Vpp

trapezoidal wave)
MPX OUT (BNC F)

composite MPX output (+6/-6dBm)

SCA IN (BNC F)

external SCA / RDS input (will be mixed to MPX output with a gain

of -20dB)
LEFT OUT (XLR M)

left channel analog output

RIGHT OUT (XLR M)

right channel analog output

RS232 (DSUB 9F)

RS232 connector

USB DRIVE (USB-A)

USB connector for fallback audio on external drive (option)

LAN (RJ45)

LAN connector (option)

Summary of Contents for DPRO3




























































Search results

Summary of Contents for DPRO3

Reviews:

Related manuals for DPRO3

Brands by name

Popular brands

Itel DPRO3, User Manual

Search results

Summary of Contents for DPRO3

Reviews:

Related manuals for DPRO3

Brands by name

Popular brands