Itel DPRO3 User Manual Download Page 13 | Manualshive

Page: 13 / 59

background image

13

Front panel display

© 2016 ITEL Elettronica e Telecominicazioni Snc

compression artifacts might become evident.

2.1.7

Band link and equalization

BandLink:

set the maximum compression difference between bass and middle/highs band.

Setting this value to zero, the bass compression level will be totally independent and this will cause
also a mild auto-equalization.
Setting this value to 100%, it will force the bass compressor to have a gain never greater than the
middle/highs band giving a sound very close to the original.

Brilliance:

high band (>6KHz) shelf equalizer.

Presence:

2KHz boost/cut filter.

2.1.8

Bass parametric eq

BassEqFreq:

parametric equalizer center frequency

BassEqGain:

gain (boost) of parametric equalizer.

BassEq Q:

Q-factor (bandwidth) of parametric equalizer.

2.1.9

Bass clipper/limiter

«
...
11
12
13
14
15
...
»

Summary of Contents for DPRO3




























































Reviews:

No comments

Related manuals for DPRO3

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 40

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 4

MYDLINK DNR-322L

Brand: D-Link Pages: 4

mydlink DNR-312L

Brand: D-Link Pages: 8

Brand: D-Link Pages: 16

Brand: D-Link Pages: 88

Brand: Xinje Pages: 76

Brand: National Instruments Pages: 11

Brand: Observint Pages: 117

Brand: Maxim Pages: 26

CompactPCI CC8-BLUES

Brand: EKF Electronik Pages: 52

Brand: Intel Pages: 958

Brand: Vega Pages: 12

DAS-1800HR Series

Brand: Keithley Pages: 139

Brand: AC Infinity Pages: 24

WAFER-EHL Series

Brand: IEI Technology Pages: 142

Brand: RadioSPECTRAL Pages: 2

Brand: ZALMAN Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands