Itel DPRO3 User Manual Download Page 54 | Manualshive

Page: 54 / 59

background image

54

DPRO3 FM Audio Processor

© 2016 ITEL Elettronica e Telecominicazioni Snc

The dynamic content has to be re-enabled from 18:00 to 23:00, so one enabling event has to be
added at 18:00 and a disabling event at 23:00.
In the following picture is represented the complete programming.

Summarizing: firstly the dynamic content enabling was added at 8:00hr, then the disabling event at
12:00hr, the re-enabling at 18:00hr and the disabling at 23:00hr.
Since this scheduling will be the same for almost the whole week, it can be simply copied to the
other days, pressing the

"Same for all days"

button.

«
...
52
53
54
55
56
...
»

Summary of Contents for DPRO3




























































Reviews:

No comments

Related manuals for DPRO3

i-bus KNX IPR/S 3.5.1

Brand: ABB Pages: 44

Brand: NEC Pages: 10

Brand: NEC Pages: 8

Brand: Javad Pages: 35

Brand: VMIC Pages: 126

Brand: Industrex Pages: 51

ACC-CX3RDK-CU5640

Brand: e-con Systems Pages: 9

Brand: RAK Pages: 30

Brand: Paradyne Pages: 10

Brand: ICP DAS USA Pages: 8

EK-FC285 GTX Classified

Brand: ekwb Pages: 2

Brand: DigiTech Pages: 6

Brand: Renesas Pages: 746

Brand: Lattice Semiconductor Pages: 43

ACCULINK 3161 CSU

Brand: Paradyne Pages: 19

Brand: Digital Audio Corporation Pages: 164

Brand: A.E.B. Pages: 28

Brand: Allen-Bradley Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands