Itel DPRO3 User Manual Download Page 10 | Manualshive

Page: 10 / 59

background image

10

DPRO3 FM Audio Processor

© 2016 ITEL Elettronica e Telecominicazioni Snc

2

Front panel display

Following are listed all menus and functionalities available on the current firmware release.

2.1

Audio processor

Into this section are comprised all functions and menus related to the audio processor.

2.1.1

Compression levels

In the window, the compression-limiting levels of the three bands are shown.
The "GTD" label, if visible, indicates that the audio level is below the gate threshold.

2.1.2

AGC

This window contains the settings for automatic gain control (AGC) block, placed at the head of
audio processing chain.
The automatic gain control performs a pre-leveling of the signal applied to the following compressors/
limiters, keeping their working point almost constant.
At the right side of the bar which indicates the level of pre-amplification applied to the input signal, is
placed the AGC status indicator: if "AGC" is displayed, the input level is above the gate threshold
and the AGC and compressors/limiters are operating correctly, if "GTD" is displayed it means that
the input signal is below the minimum level so the compressors release is slowed down and the
AGC slowly decrease its gain down to 0dB.

AGC Status (On / Off):

Enables / disables the AGC operation.

Agc Rel.Speed (0..10):

AGC release speed. By increasing this value, you will get a faster recover

when audio input gets quieter.

«
...
8
9
10
11
12
...
»

Summary of Contents for DPRO3




























































Reviews:

No comments

Related manuals for DPRO3

Brand: Samsung Pages: 2

Brand: Samsung Pages: 31

Brand: Samsung Pages: 15

Brand: Hama Pages: 12

Brand: TP-Link Pages: 2

Brand: Renesas Pages: 2

Oresund EFC102200

Brand: Bridgeworks Pages: 84

Brand: Avenview Pages: 28

See3CAM 30 Z10X

Brand: e-con Systems Pages: 14

MS-96 Vial Reader

Brand: Microscan Pages: 67

Brand: Vista Pages: 93

Brand: MESA Electronic Pages: 27

Brand: YASKAWA Pages: 87

ServCon FPS-3003

Brand: LevelOne Pages: 45

Brand: silicom Pages: 16

EK-FC670 GTX Series

Brand: ekwb Pages: 2

Brand: Hama Pages: 34

Brand: Datacom Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands