Version 3.05
| Optidrive Eco User Guide |
3
www.invertekdrives.com
Declaration of Conformity
Invertek Drives Ltd hereby states that the Optidrive Eco product range conforms to the relevant safety provisions of the following
council directives:
2014/30/EU (EMC) and 2014/35/EU (LVD)
Design and manufacture is in accordance with the following harmonised European standards:
EN 61800-5-1: 2003
Adjustable speed electrical power drive systems. Safety requirements. Electrical, thermal and energy.
EN 61800-3 2nd Ed: 2004 Adjustable speed electrical power drive systems. EMC requirements and specific test methods.
EN61000-3-12
Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current > 16
A and <= 75 A per phase.
Three phase 200V and three phase 400V Optidrive Eco products comply with IEC 61000-3-12 with respect to the
THC without the need for Line Reactors, provided that the short-circuit power Ssc is greater than or equal to SSC
(min) at the interface point between the user's supply and the public system. It is the responsibility of the installer or
user of the equipment to ensure, by consultation with the distribution network operator if necessary, that the equipment
is connected only to a supply with a short-circuit power
S
SC
greater than or equal to
S
SC (min)
calculated as:
S
SC (min)
=320 ×
V
rated
×
I
rated
Where
V
rated
is the drive rated voltage (phase to phase) and
I
rated
is the drive rated current (per phase)
EN 55011: 2007
Limits and Methods of measurement of radio disturbance characteristics of industrial, scientific and medical (ISM)
radio-frequency equipment (EMC).
EN60529: 1992
Specifications for degrees of protection provided by enclosures.
Electromagnetic Compatibility
All Optidrives are designed with high standards of EMC in mind. All versions intended for use within the European Union are fitted
with an internal EMC filter. This EMC filter is designed to reduce the conducted emissions back into the supply via the power cables
for compliance with harmonised European standards.
It is the responsibility of the installer to ensure that the equipment or system into which the product is incorporated complies with the
EMC legislation of the country of use. Within the European Union, equipment into which this product is incorporated must comply with
the EMC Directive 2004/108/EC. When using an Optidrive with an internal or optional external filter, compliance with the following
EMC Categories, as defined by EN61800-3:2004 can be achieved:
Copyright Invertek Drives Ltd © 2015
All rights reserved. No part of this User Guide may be reproduced or transmitted in any form or by any means, electrical or mechanical
including photocopying, recording or by any information storage or retrieval system without permission in writing from the publisher.
2 Year Warranty
All Invertek Optidrive Eco units carry a 2 year warranty against manufacturing defects from the date of manufacture. The manufacturer
accepts no liability for any damage caused during or resulting from transport, receipt of delivery, installation or commissioning. The
manufacturer also accepts no liability for damage or consequences resulting from inappropriate, negligent or incorrect installation,
incorrect adjustment of the operating parameters of the drive, incorrect matching of the drive to the motor, incorrect installation,
unacceptable dust, moisture, corrosive substances, excessive vibration or ambient temperatures outside of the design specification.
The local distributor may offer different terms and conditions at their discretion, and in all cases concerning warranty, the local
distributor should be contacted first.
This user guide is the “original instructions” document. All non-English versions are translations of the
“original instructions”.
The contents of this User Guide are believed to be correct at the time of printing. In the interest of a commitment to a policy of
continuous improvement, the manufacturer reserves the right to change the specification of the product or its performance or the
contents of the User Guide without notice.
This User Guide is for use with version 2.50 Firmware. The firmware version can be viewed in parameter
P0-28.
User Guide Revision 3.05
Invertek Drives Ltd adopts a policy of continuous improvement and whilst every effort has been made to provide accurate and up to
date information, the information contained in this User Guide should be used for guidance purposes only and does not form the part
of any contract.
