background image

Intesis

Box

®

 

KNX - Haier A.C. (VRF line) 

User's manual r1.0 EN 

 

 

© Intesis Software S.L.U. - All rights reserved  

This information is subject to change without notice

 

 

 

IntesisBox is a registred trademark of

 

Intesis Software SLU

 

 

 

URL 

email 

tel 

 

http://www.intesisbox.com                                          
info@intesisbox.com 
+34 938047134 

 

8 / 31 

ETS Parameters 

 
When imported to the ETS software for the first time, the gateway shows the following default 
parameter configuration: 
 

 

 

Figure 4.1 

Default parameter configuration 

 
 

With  this  configuration  it’s  possible  to  send  On/Off  (

Control_  On/Off

),  change  the  AC  Mode 

(

Control_  Mode

),  the  Fan  Speed  (

Control_  Fan  Speed

)  and  also  the  Setpoint  Temperature 

(

Control_ Setpoint Temperature

). The Status_ objects, for the mentioned Control_ objects, are 

also  available  to  use  if  needed.  Objects 

Status_  AC  Ambient  Reference  Temperature

  and 

Status_ Error/Alarm

 are shown too. 

 

 

 

 

Figure 4.2

 Default communication objects 

 

 
 
 

Summary of Contents for HA-AC-KNX-16
































Reviews: