IntesisBox HA-AC-KNX-16 User Manual Download Page 4

Page: 4 / 31

Intesis

Box

KNX - Haier A.C. (VRF line)

User's manual r1.0 EN

This information is subject to change without notice

IntesisBox is a registred trademark of

Intesis Software SLU

URL

tel

http://www.intesisbox.com
[email protected]
+34 938047134

4 / 31

INDEX

Presentation.............................................................................................................. 5

Connection ............................................................................................................... 6

Configuration and setup ............................................................................................. 7

ETS Parameters ......................................................................................................... 8

4.1

General configuration .......................................................................................... 9

4.1.1

Download latest database entry for this product and its User Manual from: .......... 9

4.1.2

Intesis Product ............................................................................................. 9

4.1.3

Number of Indoor Units in ETS ....................................................................... 9

4.1.4

First Status Updated to KNX ......................................................................... 10

4.1.5

Enable object “Error Code [2byte]”

............................................................... 10

4.1.6

Enable object “Error Text Code [14byte]”

....................................................... 10

4.2

Global mode configuration.................................................................................. 11

4.2.1

Enable use of “Operating Mode” objects

......................................................... 11

4.2.2

Enable use of Mode Heat/Cool objects ........................................................... 11

4.2.3

Enable use of + / - object for Mode ............................................................... 12

4.2.4

Enable use of bit-type Mode objects (for control) ............................................ 12

4.2.5

Enable use of bit-type Mode objects (for status) ............................................. 13

4.2.6

Enable use of Text object for Mode................................................................ 13

4.3

Global Fan Speed Configuration dialog ................................................................. 14

4.3.1

DPT object type for fan speed ....................................................................... 14

4.3.2

Enable use of “Fan Speed Man/Auto” objects (for Control and Status)

............... 15

4.3.3

Enable use of +/- object for Fan Speed .......................................................... 15

4.3.4

Enable use of bit-type Fan Speed objects (for Control) .................................... 16

4.3.5

Enable use of bit-type Fan Speed objects (for Status) ..................................... 17

4.3.6

Enable use of Text object for Fan Speed ........................................................ 17

4.4

Global temperature configuration ........................................................................ 18

4.4.1

Enable use of +/- obj for Setpoint ................................................................. 18

4.4.2

Ambient Ref. Temp. is provided from KNX ...................................................... 18

4.5

Control Mode configuration ................................................................................. 20

4.5.1

Enable use of Control Mode objects (for Control and Status) ............................ 20

4.5.1

Initial state of Control Mode ......................................................................... 20

4.6

Addressing of Indoor Units ................................................................................. 22

4.7

License ............................................................................................................ 23

Technical Specifications ............................................................................................ 24

AC Unit Types compatibility. ..................................................................................... 25

Error Codes............................................................................................................. 26

Appendix A

–

Communication Objects Table ..................................................................... 29

Summary of Contents for HA-AC-KNX-16
































Search results

Summary of Contents for HA-AC-KNX-16

Reviews:

Related manuals for HA-AC-KNX-16

Brands by name

Popular brands

IntesisBox HA-AC-KNX-16, User Manual

Search results

Summary of Contents for HA-AC-KNX-16

Reviews:

Related manuals for HA-AC-KNX-16

Brands by name

Popular brands