Intel DB75EN Specification Download

Page: 5 / 96

Preface

This Technical Product Specification (TPS) specifies the board layout, components,

connectors, power and environmental requirements, and the BIOS for Intel

Desktop

Board DB75EN.

Intended Audience

The TPS is intended to provide detailed, technical information about Intel Desktop

Board DB75EN and its components to the vendors, system integrators, and other

engineers and technicians who need this level of information. It is specifically not

intended for general audiences.

What This Document Contains

Chapter

Description

A description of the hardware used on Intel Desktop Board DB75EN

A map of the resources of the Intel Desktop Board

The features supported by the BIOS Setup program

A description of the BIOS error messages, beep codes, and POST codes

Regulatory compliance and battery disposal information

Typographical Conventions

This section contains information about the conventions used in this specification. Not

all of these symbols and abbreviations appear in all specifications of this type.

Notes, Cautions, and Warnings

NOTE

Notes call attention to important information.

CAUTION

Cautions are included to help you avoid damaging hardware or losing data.

Summary of Contents for DB75EN

































































































Search results

Summary of Contents for DB75EN

Reviews:

Related manuals for DB75EN

Brands by name

Popular brands

Intel DB75EN, Specification

Search results

Summary of Contents for DB75EN

Reviews:

Related manuals for DB75EN

Brands by name

Popular brands