Intel DB75EN Specification Download

Page: 62 / 96

Intel Desktop Board DB75EN Technical Product Specification

2.8

Reliability

The Mean Time Between Failures (MTBF) prediction is calculated using component and

subassembly random failure rates. The calculation is based on the Telcordia SR-332,

Issue 2; Method I Case 3 50% electrical stress, 50 ºC ambient. The MTBF prediction is

used to estimate repair rates and spare parts requirements. The MTBF data is

calculated from predicted data at 50 ºC. The MTBF for the Intel Desktop Board

DB75EN is 281,462 hours.

2.9

Environmental

Table 37 lists the environmental specifications for the board.

Table 37. Environmental Specifications

Parameter

Specification

Temperature

Non-Operating

-20

C to +70

Operating

C to +55

Shock

Unpackaged

50 g trapezoidal waveform

Velocity change of 170 inches/s²

Packaged

Half sine 2 millisecond

Product Weight (pounds)

Free Fall (inches)

Velocity Change (inches/s²)

<20

167

21-40

152

41-80

136

81-100

118

Vibration

Unpackaged

5 Hz to 20 Hz: 0.01 g² Hz sloping up to 0.02 g² Hz

20 Hz to 500 Hz: 0.02 g² Hz (flat)

Packaged

5 Hz to 40 Hz: 0.015 g² Hz (flat)

40 Hz to 500 Hz: 0.015 g² Hz sloping down to 0.00015 g² Hz

Summary of Contents for DB75EN

































































































Search results

Summary of Contents for DB75EN

Reviews:

Related manuals for DB75EN

Brands by name

Popular brands

Intel DB75EN, Specification

Search results

Summary of Contents for DB75EN

Reviews:

Related manuals for DB75EN

Brands by name

Popular brands