Intel DB75EN Specification Download

Page: 50 / 96

Intel Desktop Board DB75EN Technical Product Specification

2.2.2.2

Add-in Card Connectors

The board has the following add-in card connectors:

•

One PCI Express x16 (3.0/2.x/1.x)

•

One PCI Express x1 (2.x/1.x)

•

Two Conventional PCI (rev 2.3)

Note the following considerations for the Conventional PCI bus connectors:

•

The Conventional PCI bus connectors are bus master capable.

•

SMBus signals are routed to the Conventional PCI bus connectors. This enables

Conventional PCI bus add-in boards with SMBus support to access sensor data on

the desktop board. The specific SMBus signals are as follows:



The SMBus clock line is connected to pin A40.



The SMBus data line is connected to pin A41.

NOTE

PCI Express 3.0 is only supported by 3

generation Intel Core processor family

processors.

Summary of Contents for DB75EN

































































































Search results

Summary of Contents for DB75EN

Reviews:

Related manuals for DB75EN

Brands by name

Popular brands

Intel DB75EN, Specification

Search results

Summary of Contents for DB75EN

Reviews:

Related manuals for DB75EN

Brands by name

Popular brands