Intel DB75EN Specification Download

Page: 89 / 96

Regulatory Compliance and Battery Disposal Information

5.1.6

ENERGY STAR* 5.0, e-Standby, and ErP

Compliance

The US Department of Energy and the US Environmental Protection Agency have

continually revised the ENERGY STAR requirements. Intel has worked directly with

these two governmental agencies in the definition of new requirements.

Intel Desktop Board DB75EN meets the following program requirements in an

adequate system configuration, including appropriate selection of an efficient power

supply:

•

Energy Star v5.0, category D

•

EPEAT*

•

Korea e-Standby

•

European Union Energy-related Products Directive 2009 (ErP) Lot 6

NOTE

Energy Star compliance is based at the system level not the board level. Use of an

Intel Desktop Board alone does not guarantee Energy Star compliance.

For information about

Refer to

ENERGY STAR requirements and recommended configurations

http://www.intel.com/go/energystar

Electronic Product Environmental Assessment Tool (EPEAT)

http://www.epeat.net/

Korea e-Standby Program

http://www.kemco.or.kr/new_eng/pg02/
pg02100300.asp

European Union Energy-related Products Directive 2009 (ErP)

http://ec.europa.eu/enterprise/policies/s
ustainable-business/sustainable-
product-policy/ecodesign/index_en.htm

Summary of Contents for DB75EN

































































































Search results

Summary of Contents for DB75EN

Reviews:

Related manuals for DB75EN

Brands by name

Popular brands

Intel DB75EN, Specification

Search results

Summary of Contents for DB75EN

Reviews:

Related manuals for DB75EN

Brands by name

Popular brands