Intel DB75EN Specification Download

Page: 28 / 96

Intel Desktop Board DB75EN Technical Product Specification

1.9.2

LAN Subsystem Software

LAN software and drivers are available from Intel’s World Wide Web site.

For information about

Refer to

Obtaining LAN software and drivers

http://downloadcenter.intel.com

1.9.3

RJ-45 LAN Connector with Integrated LEDs

Two LEDs are built into the RJ-45 LAN connector (shown in Figure 5).

Item Description

Link LED (Green)

Data Rate LED (Green/Yellow)

Figure 5. LAN Connector LED Locations

Table 6 describes the LED states when the board is powered up and the LAN

subsystem is operating.

Table 6. LAN Connector LED States

LED

LED Color

LED State

Condition

Link

Green

Off

LAN link is not established.

LAN link is established.

Blinking

LAN activity is occurring.

Data Rate

Green/Yellow

Off

10 Mb/s data rate is selected.

Green

100 Mb/s data rate is selected.

Yellow

1000 Mb/s data rate is selected.

Summary of Contents for DB75EN

































































































Search results

Summary of Contents for DB75EN

Reviews:

Related manuals for DB75EN

Brands by name

Popular brands

Intel DB75EN, Specification

Search results

Summary of Contents for DB75EN

Reviews:

Related manuals for DB75EN

Brands by name

Popular brands