Intel CELERON PROCESSOR E3000 - THERMAL AND MECHANICAL DESIGN Design Manual Download | Manualshive

Page: 64 / 126

background image

Intel® Quiet System Technology (Intel® QST)

64

Thermal and Mechanical Design Guidelines

Figure 7-1. Intel

®

QST Overview

7.1.1

Output Weighting Matrix

Intel QST provides an Output Weighting Matrix that provides a means for a single
thermal sensor to affect the speed of multiple fans. An example of how the matrix
could be used is if a sensor located next to the memory is sensitive to changes in both
the processor heatsink fan and a 2

nd

fan in the system. By placing a factor in this

matrix additional, the Intel QST could command the processor thermal solution fan
and this 2

nd

fan to both accelerate a small amount. At the system level these two

small changes can result in a smaller change in acoustics than having a single fan
respond to this sensor.

7.1.2

Proportional-Integral-Derivative (PID)

The use of Proportional-Integral-Derivative (PID) control algorithms allow the
magnitude of fan response to be determined based upon the difference between
current temperature readings and specific temperature targets. A major advantage of
a PID Algorithm is the ability to control the fans to achieve sensor temperatures much
closer to the T

CONTROL

.

Figure 7-2 is an illustration of the PID fan control algorithm. As illustrated in the
figure, when the actual temperature is below the target temperature, the fan will slow
down. The current FSC devices have a fixed temperature versus PWM output
relationship and miss this opportunity to achieve additional acoustic benefits. As the
actual temperature starts ramping up and approaches the target temperature, the
algorithm will instruct the fan to speed up gradually, but will not abruptly increase the
fan speed to respond to the condition. It can allow an overshoot over the target
temperature for a short period of time while ramping up the fan to bring the actual

Fan to sensor

Relationship

(Output Weighting Matrix)

Temperature sensing

and response

Calculations

(PID)

Fan Commands

(PID)

Fans

Temperature

Sensors

Intel

®

QST

System Response

PWM

PECI / SST

«
...
62
63
64
65
66
...
»

Summary of Contents for CELERON PROCESSOR E3000 - THERMAL AND MECHANICAL DESIGN































































































































Reviews:

No comments

Related manuals for CELERON PROCESSOR E3000 - THERMAL AND MECHANICAL DESIGN

Brand: 3Com Pages: 20

Brand: Rabbit Pages: 45

Brand: Rabbit Pages: 174

Brand: Rabbit Pages: 43

Brand: National Instruments Pages: 28

Brand: National Instruments Pages: 19

Brand: National Instruments Pages: 103

NI PXI-1042 Series

Brand: National Instruments Pages: 12

Brand: National Instruments Pages: 4

Brand: Zhone Pages: 1

nForce 680I LT SLI

Brand: Nvidia Pages: 80

Brand: ZALMAN Pages: 9

Brand: EVOC Pages: 57

Brand: QNAP Pages: 54

Brand: IDT Pages: 207

Brand: AMD Pages: 45

Brand: ExtraHop Pages: 3

ROScube-I Series

Brand: ADLINK Technology Pages: 95

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands