InnovaPrep Concentrating Pipette Select User Manual Download Page 17

Page: 17 / 37

Patented

https://www.innovaprep.com/patents

5.3

AINTENANCE

ENU

Selecting

Maintenance

from the Main Menu will display instrument procedures (see Section 6

Maintenance

Procedures

Start Up

Shut Down

Prime

Elute

Return

•

Selecting

Start Up

will take the user through a series of prompts for the daily Start Up procedure (see Section

6.2

Start Up Procedure

•

Selecting

Shut Down

will take the user through a series of prompts for the daily Shut Down procedure (see

Section 6.3

Shut Down Procedure

•

Prime

is for priming the elution fluid lines when a new elution fluid canister is installed in the unit. This

ensures that there is no air in the fluid path (see Section 6.4

Priming the Elution Fluid

•

Elute

performs a foam elution according to the current instrument settings. This can be used at any time to

test the elution settings (see Section 8

The Elute Function

•

Return

will lead back to the Main Menu.

5.4

NSTRUMENT

ETTINGS

ENU

There are seven instrument settings. A description of each are listed below:

•

Beep volume

changes the volume of the beeps that occur at the end of concentration cycles and elutions.

The four options are

low

med.

high

, and

off

. Default = low

•

Power LED

turns the blue LED light in the Fluidics head on and off. Default = on

•

Run LED

turns the flashing red LED light in the Fluidics head on and off. Default = on

•

Elute LED

turns the flashing green LED light in the Fluidics head on and off. Default = on

•

Set Password

allows the user to set a password that must be entered before a custom protocol can be

created, modified, or deleted.

•

Protocol

allows the user

to set the instrument to standard (

Std

) or advanced (

Adv

) options. If set to

Std

, the

user will have access to two standard set points -

Valve Open

and

Pulse Count

. If set to

Adv,

the user will

have access to 11 advanced settings during Protocol Creation. Once set, the options are accessed in the
Protocol Setup menu under Create Protocol. Default = Std

•

Fluid Gauge

turns the Elution Fluid Volume gauge on and off. Default = on

•

Return

will return you to the Options menu.

FIGURE 5.3 MAINTENANCE DISPLAY

Summary of Contents for Concentrating Pipette Select





































Search results

Summary of Contents for Concentrating Pipette Select

Reviews:

Related manuals for Concentrating Pipette Select

Brands by name

Popular brands

InnovaPrep Concentrating Pipette Select, User Manual

Search results

Summary of Contents for Concentrating Pipette Select

Reviews:

Related manuals for Concentrating Pipette Select

Brands by name

Popular brands