InnovaPrep Concentrating Pipette Select User Manual Download Page 6

Page: 6 / 37

Patented

https://www.innovaprep.com/patents

•

Silicone Lubricant

(HC08535) – Used for required, periodic lubrication of O-rings in the Tip Interface Port. See

Section 4.5.

•

Storage Fluid Adapter

(HC08560) – Connects storage fluid bottle, required in daily Shut Down maintenance

procedure. See Section 4.3.

•

Maintenance Tip

(HC08005) – This reusable tip is inserted into the Tip Interface Port during the

Start Up,

Shut

Down

and

Prime

maintenance procedures. DO NOT USE WITH THE ELUTE OR RUN PROTOCOL-DAMAGE CAN

OCCUR TO THE INSTRUMENT. See Section 6.

•

Alcohol Prep Pads

(HC08529) – Used for periodic cleaning of the tip and elution fluid ports.

•

Filterless Tip

(HC08524 - M) – Used for alternate cleaning and maintenance procedures. Also, for

troubleshooting and diagnostic procedures when consulting with InnovaPrep Technical Support Engineers.
Keep on hand.

•

11 µm Nylon Syringe Filter 25mm

(HC08533) – Used for alternate cleaning and maintenance procedures.

Summary of Contents for Concentrating Pipette Select





































Search results

Summary of Contents for Concentrating Pipette Select

Reviews:

Related manuals for Concentrating Pipette Select

Brands by name

Popular brands

InnovaPrep Concentrating Pipette Select, User Manual

Search results

Summary of Contents for Concentrating Pipette Select

Reviews:

Related manuals for Concentrating Pipette Select

Brands by name

Popular brands