Ingersoll-Rand Trane Ascend ACS, Installation, Operation And Maintenance Manual

Page: 86 / 88

86 AC-SVX002C-EN
Ascend ™ ™ Model ACS
Installation Completion Check
Sheet and Request for Trane
Service
IIm mp po orrtta an ntt:: A copy of this completed form must be
submitted to the Trane service agency that
will be responsible for the start-up of the
chiller. Start-up will NOT proceed unless
applicable items listed in this form have
been satisfactorily completed.
To:
Trane Service Office:
S.O. Number:
Serial Numbers:
Job/Project Name:
Address:
The following items
are being installed
and will be completed by:
IIm mp po orrtta an ntt:: Start-up must be performed by Trane or an
agent of Trane specifically authorized to
perform start-up and warranty of Trane®
products. Contractor shall provide Trane
(or an agent of Trane specifically
authorized to perform start-up) with notice
of the scheduled start-up at least two weeks
prior to the scheduled start-up.
IIm mp po orrtta an ntt:: IItt iiss rre eq qu uiirre ed d tth ha att h he ea atte errss a arre e e en ne errg giizze ed d
ffo orr a a m miin niim mu um m o off 2 24 4 h ho ou urrss p prriio orr tto o sstta arrtt
u up p.. T Th he erre effo orre e,, cch hiilllle err ssh ho ou ulld d h ha av ve e p po ow we err
ffo orr tth hiiss a am mo ou un ntt o off ttiim me e b be effo orre e T Trra an ne e
S Se errv viicce e a arrrriiv ve ess tto o d do o sstta arrtt--u up p..
Check boxes if the task is complete or if the answer is
“yes”.
1. C Ch hiilllle err
☐ Installation meets foundation requirements
☐ In place and piped.
☐ Isolation pads or elastomeric isolators installed.
☐ Chiller is level to within 1/4" end-to-end and
side-to-side.
☐ Record and report any damage to the chiller.
2. P Piip piin ng g
☐ Water piping flushed before making final
connections to the system
☐ Chilled water piping connected to:
☐
Evaporator
☐ Air handling units
☐ Pumps (no piping to pump required if
optional pump package is installed)
☐ Strainer installed and cleaned at entering water
connection
N No otte e:: Do NOT remove strainer mesh to clean
the system.
☐
Verify chilled water inlet vents and chilled water
outlet drains are closed or plugs installed
☐ Water supply connected to filling system
☐ Does unit have freeze inhibitor? If unit has
freeze inhibitor:
☐ Verify type and concentration correct per
unit submittal
☐ Calculate and record freeze point of the
solution: __________
☐ Systems filled
☐ Pumps run, air bled from system
☐ Relief valve ventilation piping installed (if
applicable)
☐ Flow balancing valves installed on leaving
chilled water
☐ Gauges, thermometers, and air vents installed
on both sides of evaporator
3. W Wiirriin ng g
☐ Wire size per submittal and NEC 310-16
☐ Unit is properly grounded
☐ All wiring connections are tight (not limited to
field wiring - include factory wiring and
connections)
☐ Full power available, and within utilization
range
☐ Interconnecting wiring to control panel (as
required)
☐ Chilled water pump connected and tested (not
required if optional pump package is installed)
☐ Heat recovery condenser water pump (as
applicable)
☐ 115 Vac power available for service tools
☐ All controls installed and connected
4. T Te essttiin ng g
☐ Trace gas amounts of R-410A available for leak
testing, if necessary
L Lo og g a an nd d C Ch he ecckk S Sh he ee ettss