In-situ Level TROLL 400 Operator'S Manual Download Page 41 | Manualshive

Page: 41 / 85

In-situ Level TROLL 400 Operator'S Manual Download Page 41

1-800-446-7488

41

www.in-situ.com

BaroTROLL Instrument Installation

The BaroTROLL Instrument is designed to log barometric pressure from 0 to 16.5 PSIA (1.14 bar, 33.59 inHg) at the surface
near a submerged non-vented Level TROLL Instrument or Aqua TROLL 200 Instrument. BaroTROLL data may then be used
to correct the water level data for barometric pressure fluctuations. See page 15.

Programming the Baro TROLL Instrument

Connect the BaroTROLL to Win-Situ 5 software or the VuSitu mobile app and sync the clock.See page 53.

Set up a log with the same start time and sample interval as you set up in the non-vented level instrument. See page 54.

Installation

After the BaroTROLL Instrument is programmed, install it in a protected location above the water level near the submerged
water level instrument. One installation configuration option is shown below using a twist-lock hanger and a suspension wire.

To prevent flooding of the BaroTROLL electronics, attach the twist-lock hanger before you
install the BaroTROLL. Do not submerge the Baro TROLL Instrument.

«
...
39
40
41
42
43
...
»

Summary of Contents for Level TROLL 400






















































































Reviews:

No comments