In-situ Level TROLL 400 Operator'S Manual Download Page 35

Page: 35 / 85

1-800-446-7488

www.in-situ.com

Connecting RuggedCable

Connect the Instrument to the RuggedCable

1. Remove the protective caps from the instrument and cable. Ensure that the O-ring on the instrument connector is

clean. Apply a small amount of vacuum grease to the o-ring.

2. Position the instrument and cable flat edges so they will connect properly. Insert the instrument connector firmly

into the cable connector.

3. Hold the textured section of the sleeve in one hand and the instrument in the other. Push and twist until you hear a

click. The click ensures the cable and instrument are securely attached.

Connect TROLL Com Communication Device to the RuggedCable System

1. If a desiccant is present, remove the desiccant from the cable. Twist the desiccant and cable sleeve in opposite

directions to unlock the desiccant from the cable.

2. Position the TROLL Com and cable flat edges so they will connect properly. Push and twist until you hear a click.

Summary of Contents for Level TROLL 400






















































































Search results

Summary of Contents for Level TROLL 400

Reviews:

In-situ Level TROLL 400, Operator'S Manual, Page: 35 / 85

Search results

Summary of Contents for Level TROLL 400

Reviews: