Immergas ZEUS 24 Superior, Instruction Booklet And Warning

Page: 10 / 28

10
C12
1-18
C12
1-19
C32
1-21 1-20
C32
1
2
6
4
3
5
6
2
1
3
4
5
7
8
*
*
INS
TALL
AT
O
R
US
ER
MAINTEN
AN
CE
M
ax 12200 mm
M
ax 4700 mm
The kit includes:
N°1 - Seal (1)
N°1 - Concentric bend Ø 60/100 (2)
N°1 - Adapter Ø 60/100 for Ø 80/125 (3)
N°1 - Concentric intake/exhaust
terminal Ø 80/125
N°1 - Internal ring (5)
N°1 - External ring (6)
• Coupling extension pipes and concentric el-
bows. To install possible coupling extensions
on other fume extraction elements, proceed
as follows: fit the male end (smooth) of the
concentric pipe or concentric elbow up to the
stop on the female end (with lip seals) of the
previously installed element; this will ensure
correct hold and joining of the elements.
Caution:
if the exhaust terminal and/or exten-
sion concentric pipe needs shortening, consider
that the internal duct must always protrude by 5
mm with respect to the external duct.
This specific terminal enables flue exhaust and
air intake in a vertical direction.
N.B.:
the vertical kit Ø 80/125 with aluminium
tile enables installation on terraces and roofs with
maximum slope of 45% (24°). The height between
the terminal cap and half-shell (374 mm) must
always be respected.
The vertical kit with this configuration can be
extended up to a
maximum of 12200 mm
vertical
rectilinear, including the terminal (Fig. 1-21).
This configuration correspondsto a resistance
factor of 100. In this case specific extensions
must be requested.
The terminal Ø 60/100 can also be used for
vertical exhaust, in conjunction with concentric
flange code no. 3.011141 (sold separately). The
The kit includes:
N°1 - Seal (1)
N°1 - Female concentric flange (2)
N°1 - Adapter Ø 60/100 for Ø 80/125 (3)
N°1 - Ring (4)
N°1 - Aluminium tile (5)
N°1 - Intake/Exhaust concentric pipe
Ø 80/125 (6)
N°1 - Fixed semi-shell (7)
N°1 - Mobile half-shell (8)
height between the terminal cap and half-shell
(374 mm) must always be respected (Fig. 1-21).
The vertical kit with this configuration can be
extended to a max. straight vertical length of 4700
mm, including the terminal (Fig. 1-21).
Separator kit Ø 80/80. The separator kit Ø 80/80,
enables separation of the exhaust flues and air
intake pipes according to the diagram shown in
the figure. (Fig. 1-22). Fumes are expelled from
duct (S). Air is taken in through duct (A) for
combustion. Intake duct (A) can be installed
either on the right or left hand side of the central
exhaust duct (S). Both ducts can be routed in
any direction.
• Assembly of separator kit Ø 80/80. Install the
flange (4) on the central hole of the boiler
inserting the seal (1) and tighten using the
hex and flathead screws supplied with the
kit. Remove the flat flange in the lateral hole
with respect to the central one (depending on
installation requirements) and replace with
flange (3) inserting the seal (2) already fitted
on the boiler and tighten using the self-tapping
screws supplied. Fit the male end (smooth) of
the bends (5) in the female end of the flanges (3
and 4). Fit the male end (smooth) of the intake
terminal (6) up to the stop on the female end
of the bend (5), making sure that the relevant
internal and external rings are fitted. Join the
exhaust pipe (9) with the male section (smooth)
in the female section of the bend (5) to the end
stop, ensuring that the internal washer is fitted;
this will ensure the sealing efficiency of the kit
components.
• Snap fit extension pipe fittings and elbows. To
install snap-fit extensions with other elements
of the fume extraction elements assembly,
proceed as follows: fit the pipe or elbow with
the male section (smooth) in the female section
(with lip seal) to the end stop on the previously
installed element; in this way sealing efficiency
of the couplings is assured.
• The figure (Fig. 1-24) shows the configuration
with vertical exhaust and horizontal intake.
• Installation clearances. The figure (Fig. 1-23)
gives the min. installation space dimensions
of the Ø 80/80 separator terminal kit al limit
condition.
• Extensions for separator kit Ø 80/80. The max.
vertical straight length (without bends) usable
for Ø 80 intake and exhaust pipes is 41 metres
of which 40 intake and 1 exhaust. This total
length corresponds to a resistance factor of 100.
The total usable length, obtained by adding the
length of the intake and exhaust pipes Ø 80,
must not exceed the maximum values given
in the following table. If mixed accessories or
components (are used (e.g. changing from a