ILC Dover S-5000 Series User Instruction Manual Download Page 22 | Manualshive

Page: 22 / 40

background image

- 21 -

S-2018

REV. D

8. Take the hood out of the designated hood Compartment. Remove hood from fabric bag.

9. Connect the Hood’s Breathing Tube to the Blower.

  •  Confirm that the breathing tube thread has the black rubber gasket seal present.
  •  Confirm that the thread in the blower unit is in good condition and clear of foreign matter.
  •  Screw the end of the breathing tube into the blower unit until it is hand tight. Ensure that there is not

excessive twist on the hose. If so, loosen the breathing tube fitting where it attaches to the blower, rotate

the hose to eliminate the twist, and retighten the fitting.

Do not over-tighten!

«
...
20
21
22
23
24
...
»

Summary of Contents for S-5000 Series









































Reviews:

No comments

Related manuals for S-5000 Series

OptiChamber Diamond

Brand: PHILIPS Respironics Pages: 2

Brand: PHILIPS Respironics Pages: 179

Brand: Kimberly-Clark Pages: 5

Brand: ekastu Pages: 15

FreshAir Flow Control

Brand: Kempi Pages: 18

Brand: Pari Pages: 8

BiWaze Clear System

Brand: ABM Pages: 12

Brand: Urrea Pages: 4

Brand: Sleepnet Pages: 14

Brand: Roscoe Medical Pages: 8

Brand: Roscoe Medical Pages: 16

Brand: Ops-Core Pages: 20

MAGNUM M23/1000

Brand: MARTINDALE Pages: 8

Brand: eMoyo Pages: 2

Brand: Chicco Pages: 88

SUPER SOFT 00009067000000

Brand: Chicco Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands