IEMCA SIR52 MS52 F Manual For Use And Maintenance Download Page 138

Page: 138 / 212

9 - PART REPLACEMENT

SIR 52 MS52 P/F

9 - Pag. 6 / 16

9.5

CAPACITIVE SENSOR - REPLACEMENT

- Replace the capacitive sensor.
- Position a 4 mm ø bar on the lifted loading

levers.

- Adjust the sensitivity of the sensor by setting it

at the minimum value.

- Gradually increase the sensibility until the

luminous led (A) switches on.

- Said led must switch off when the bar is

removed.

9.6

GUIDE CONTROL SENSORS - REPLACEMENT

Guide closing sensors

- Replace the sensors (A).
- Adjust their position on the diameter Ø (B) of

the rod, not on diameter Ø (C).

CAUTION:

If the position of the sensors were

adjusted on diameter ø (C), they would

be cut during rod extension.

Summary of Contents for SIR52 MS52 F





















































































































































































































Search results

Summary of Contents for SIR52 MS52 F

Reviews:

Related manuals for SIR52 MS52 F

Brands by name

Popular brands

IEMCA SIR52 MS52 F, Manual For Use And Maintenance

Search results

Summary of Contents for SIR52 MS52 F

Reviews:

Related manuals for SIR52 MS52 F

Brands by name

Popular brands