IEI Technology TANK-870AI SERIES User Manual Download

Page: 46 / 137

TANK-870AI Embedded System

Page 32

Step 2:

Insert the serial connector

Insert the DB-9 connector of a serial device into

the DB-9 connector on the external peripheral interface. See

Figure 3-19

Figure 3-19: Serial Device Connector

Step 3:

Secure the connector

. Secure the serial device connector to the external

interface by tightening the two retention screws on either side of the connector.

Figure 3-20: DB-9 RS-232/422/485 Serial Port Connector

3.6.11 USB Connectors

The USB ports are for connecting USB peripheral devices to the system.

Step 1:

Locate the USB connectors

. The locations of the USB connectors are shown

Figure 1-3

Summary of Contents for TANK-870AI SERIES










































































































































Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands

IEI Technology TANK-870AI SERIES, User Manual

Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands