IEI Technology TANK-870AI SERIES User Manual Download

Page: 106 / 137

TANK-870AI Embedded System

Page 92



Disabled



Enabled

Default



PCIe Speed

Use PCIe Speed option to select the speed type of the PCIe Mini slot. The following

options are available:



Auto

Default



Gen1



Gen2



Gen3

5.4.2.2 HD Audio Configuration

Use the

HD Audio Configuration

submenu (

BIOS Menu 25

) to configure the High

Definition Audio codec.

Chipset

HD Audio Configuration

HD Audio

[Auto]

Control Detection of the
Azalia device.
Disable = Azalia will be
unconditionally disabled
Enabled = Azalia will be
unconditionally Enabled.
Auto = Azalia will be
enabled if present,
disabled otherwise.

---------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+ - Change Opt.
F1

General Help

Previous Values

Optimized Defaults

Save & Exit

ESC Exit

BIOS Menu 25: HD Audio Configuration

Summary of Contents for TANK-870AI SERIES










































































































































Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands

IEI Technology TANK-870AI SERIES, User Manual

Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands