IEI Technology TANK-870AI SERIES User Manual Download

Page: 78 / 137

TANK-870AI Embedded System

Page 64



C State [Disabled]

Use the

C State

option to enable or disable CPU C State.



Disabled

EFAULT

Disables CPU C State.



Enabled

Enables CPU C State.

5.3.2 Trusted Computing

Use the

Trusted Computing

menu (

BIOS Menu 4

) to configure settings related to the

Trusted Computing Group (TCG) Trusted Platform Module (TPM).

Advanced

TPM20 Device Found

Security Device Support

[Enable]

Pending operation

[None]

Enables or Disables BIOS
support for security
device. O.S. will not
show Security Device.
TCG EFI protocol and
INT1A interface will not
be available.
----------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 4: Trusted Computing



Security Device Support [Enable]

Use the

Security Device Support

option to configure support for the security device.



Disable

Security device support is disabled.



Enable

EFAULT

Security device support is enabled.

Summary of Contents for TANK-870AI SERIES










































































































































Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands

IEI Technology TANK-870AI SERIES, User Manual

Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands