IEI Technology SPCIE-C2260-i2 Page 77 User Manual Download

Page: 77 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 61

4.4.2 CPU Card Installation

To install the CPU card onto the backplane, carefully align the CPU card edge connector

with the CPU card socket on the backplane. To do this, please refer to the reference

material that came with the backplane. Next, secure the CPU card to the chassis. To do

this, please refer to the reference material that came with the chassis.

4.5 Internal Peripheral Device Connections

This section outlines the installation of peripheral devices to the onboard connectors.

4.5.1 Dual RS-232 Cable with Slot Bracket

The dual RS-232 cable slot connector consists of two connectors attached to two

independent cables. Each cable is then attached to a D-sub 9 male connector that is

mounted onto a slot. To install the dual RS-232 cable, please follow the steps below.

Step 1:

Locate the connectors

. The locations of the RS-232 connectors are shown in

Chapter 3

Step 2:

Insert the cable connectors

. Insert one connector into each serial port box

headers (

Figure 4-11

). A key on the front of the cable connectors ensures the

connector can only be installed in one direction.

Figure 4-11: Dual RS-232 Cable Installation

Summary of Contents for SPCIE-C2260-i2



































































































































































Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands

IEI Technology SPCIE-C2260-i2, User Manual

Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands