IEI Technology SPCIE-C2260-i2 Page 129 User Manual Download

Page: 129 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 113



Quiet Boot [Enabled]

Use the

Quiet Boot

BIOS option to select the screen display when the system boots.



Disabled

Normal POST messages displayed



Enabled

EFAULT

OEM Logo displayed instead of POST messages



Option ROM Messages [Force BIOS]

Use the

Option ROM Messages

option to set the Option ROM display mode.



Force

BIOS

EFAULT

Sets display mode to force BIOS.



Keep

Current

Sets display mode to current.



Launch PXE OpROM [Disabled]

Use the

Launch PXE OpROM

option to enable or disable boot option for legacy network

devices.



Disabled

EFAULT

Ignore all PXE Option ROMs



Enabled

Load PXE Option ROMs.



UEFI Boot [Disabled]

Use the

UEFI Boot

option to enable or disable to boot from the UEFI devices.



Enabled

Boot from UEFI devices is enabled.



Disabled

EFAULT

Boot from UEFI devices is disabled.

Summary of Contents for SPCIE-C2260-i2



































































































































































Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands

IEI Technology SPCIE-C2260-i2, User Manual

Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands