IEI Technology SPCIE-C2260-i2 Page 96 User Manual Download

Page: 96 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 80

Advanced

Configuration

Security Device Support

[Disable]

Current Status Information

NO Security Device Found

Enables or Disables BIOS
support for security
device. O.S. will not
show Security Device.
TCG EFI protocol and
INT1A interface will not
be available.

----------------------



: Select Screen

↑

↓

: Select Item

Enter:  Select
+/-:  Change Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 5: Trusted Computing



Security Device Support [Disable]

Use the

Security Device Support

option to configure support for the TPM.



Disable D

EFAULT

TPM support is disabled.



Enable

TPM support is enabled.

Summary of Contents for SPCIE-C2260-i2



































































































































































Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands

IEI Technology SPCIE-C2260-i2, User Manual

Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands