manualshive.com logo in svg

IEI Technology SPCIE-C2260-i2, User Manual, Page: 70 / 162

Share
Download
IEI Technology SPCIE-C2260-i2 User Manual Download Page 70

 

 

SPCIE-C2260-i2 PICMG 1.3 CPU Card 

Page 54 

Step 9: 

Connect the 12 V power to the board.

 Connect the 12 V power from the power 

supply to the board. 

Step 0:

 

4.2.2 Socket LGA1150 Cooling Kit Installation 

  WARNING: 

DO NOT attempt to install a push-pin cooling fan. 

The pre-installed support bracket prevents the board from 

bending and is ONLY compatible with captive screw type cooling 

fans.

 

 

The cooling kit can be bought from IEI. The cooling kit has a heat sink and fan. 

  WARNING: 

Do not wipe off (accidentally or otherwise) the pre-sprayed layer of 

thermal paste on the bottom of the  heat sink. The thermal paste 

between the CPU and the heat sink is important for optimum heat 

dissipation. 

To install the cooling kit, follow the instructions below. 

Step 1: 

A cooling kit bracket is pre-installed on the rear of the motherboard. See 

Figure 

4-5.

   

Summary of Contents for SPCIE-C2260-i2



































































































































































Reviews:

No comments