IEI Technology SPCIE-C2260-i2 Page 18 User Manual Download

Page: 18 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 2

1.1 Introduction

Figure 1-1: SPCIE-C2260-i2

The SPCIE-C2260-i2 is a PICMG 1.3 CPU card. It accepts a Socket LGA1150 Intel®

Xeon® E3, Core™ i3, Pentium® or Celeron® processor and supports four 240-pin

1600/1333 MHz dual-channel DDR3 DIMM modules up to 32 GB.

The SPCIE-C2260-i2 provides two GbE interfaces through the Intel® I217LM (with Intel®

AMT 9.0 support) and the Intel® I210 PCIe controllers. The integrated Intel® C226 chipset

supports six SATA 6Gb/s drives. In addition, the SPCIE-C2260-i2 includes VGA and iDP

interfaces for dual independent display.

Two USB 3.2 Gen 1 (5Gb/s) on the rear panel, two

USB 3.2 Gen 1 (5Gb/s) by pin header,

four USB 2.0 by pin headers, four USB 2.0 by pin headers on backplane, four RS-232 and

one PCIe Mini interface with mSATA support provide flexible expansion options. High

Definition Audio (HDA) support ensures HDA devices can be easily implemented on the

SPCIE-C2260-i2.

Summary of Contents for SPCIE-C2260-i2



































































































































































Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands

IEI Technology SPCIE-C2260-i2, User Manual

Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands