IEI Technology SPCIE-C2260-i2 Page 37 User Manual Download

Page: 37 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 21

3.2.3 Battery Connector

CAUTION:

Risk of explosion if battery is replaced by an incorrect type. Only

certified engineers should replace the on-board battery.

Dispose of used batteries according to instructions and local

regulations.

CN Label:

BAT1

CN Type:

2-pin wafer

CN Location:

See

Figure 3-4

CN Pinouts:

See

Table 3-5

This is connected to the system battery. The battery provides power to the system clock to

retain the time when power is turned off.

NOTE

: It is recommended to attach the RTC

battery onto the system chassis in which the SPCIE-C2260-i2 is installed.

Figure 3-4: Battery Connector Location

Pin

Description

VBATT

GND

Table 3-5: Battery Connector (BAT1) Pinouts

Summary of Contents for SPCIE-C2260-i2



































































































































































Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands

IEI Technology SPCIE-C2260-i2, User Manual

Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands