background image

 

 

SPCIE-C2260-i2 PICMG 1.3 CPU Card 

Page 8 

I/O Interface Connectors 

Audio Connector 

One internal audio connector (10-pin header) 

Chassis Intrusion 

One

 

2-pin header 

Digital I/O 

8-bit digital I/O 

Display Output 

One VGA (up to 1920 x 1200, 60 Hz) 

One iDP interface for HDMI, LVDS, VGA, DVI and DisplayPort (up to   

3840 x 2160, 60 Hz) 

Ethernet 

Two RJ-45 GbE ports 

Fan 

One 4-pin smart fan connector (CPU fan) 

One 3-pin fan connector (system fan)

 

Front Panel 

One 14-pin header (power LED, HDD LED, IPMI LED, speaker, power 

button, reset button) 

Infrared 

One via 5-pin header 

IPMI 2.0 

One iRIS module slot 

Keyboard and Mouse 

One 6-pin wafer connector 

LAN LEDs 

Two

 

2-pin headers for LAN1 LED and LAN2 LED (active) 

Parallel Port 

One parallel port via internal 26-pin box header 

Serial ATA 

Six SATA 6Gb/s connectors (support RAID 0, 1, 5, 10) 

Serial Ports 

Four RS-232 via internal box headers 

One RS-422/485 via internal 4-pin wafer connector 

SMBus 

One 4-pin wafer connector 

TPM 

One via 20-pin header 

USB Ports 

Two external USB 3.2 Gen 1 (5Gb/s) ports on rear IO 

Two internal USB 3.2 Gen 1 (5Gb/s) ports by pin header 

Four internal USB 2.0 ports by pin headers 

Four internal USB 2.0 ports by pin headers on backplane 

Environmental and Power Specifications 

Power Supply 

5V/12V, AT/ATX power supported 

Summary of Contents for SPCIE-C2260-i2



































































































































































Reviews: