IEI Technology SPCIE-C2260-i2 Page 121 User Manual Download

Page: 121 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 105



PCIe Speed [Gen1]

Use this option to select the support type of the PCI Express ports. The following options

are available:



Auto

Default



Gen1



Gen2



Detect Non-Compliance Device [Enabled]

Use the

Detect Non-Compliance Device

option to enable or disable detecting if a

non-compliance PCI Express device is connected to the PCI Express port.



Disabled

Disables to detect if a non-compliance PCI

Express device is connected to the PCI Express

port.



Enabled

EFAULT

Enables to detect if a non-compliance PCI Express

device is connected to the PCI Express port.

5.4.1.2 PCH Azalia Configuration

Use the

PCH Azalia Configuration

menu (

BIOS Menu 23

) to configure the PCH Azalia

settings.

Summary of Contents for SPCIE-C2260-i2



































































































































































Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands

IEI Technology SPCIE-C2260-i2, User Manual

Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands