manualshive.com logo in svg

IEI Technology ISP-9652/9602, User Manual

Share
Download
IEI Technology ISP-9652/9602 User Manual Download Page 93

 

 

ISP-9652/9602 User Manual 

Page 81

Î

 

Available D

EFAULT

 

The specified IRQ is available to be used by 

PCI/PnP devices 

Î

 

Reserved  

The specified IRQ is reserved for use by Legacy ISA 

devices 

Available IRQ addresses are: 

ƒ

 IRQ3 

ƒ

 IRQ4 

ƒ

 IRQ5 

ƒ

 IRQ7 

ƒ

 IRQ9 

ƒ

 IRQ10 

ƒ

 IRQ 

11 

ƒ

 IRQ 

14 

ƒ

 IRQ 

15 

Î

 

DMA Channel# [Available] 

Use the 

DMA Channel# 

option to assign a specific DMA channel to a particular PCI/PnP 

device. 

Î

 

Available D

EFAULT

 

The specified DMA is available to be used by 

PCI/PnP devices 

Î

 

Reserved  

The specified DMA is reserved for use by Legacy 

ISA devices 

Available DMA Channels are: 

ƒ

 

DM Channel 0 

ƒ

 

DM Channel 1 

ƒ

 

DM Channel 3 

ƒ

 

DM Channel 5 

ƒ

 

DM Channel 6 

ƒ

 

DM Channel 7 

Summary of Contents for ISP-9652/9602
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands