IEI Technology ISP-9652/9602 User Manual Download Page 83

Page: 83 / 119

ISP-9652/9602 User Manual

Page 71

Automatic mode

The fan adjusts its speed using these settings:

Temp. Limit of OFF

Temp. Limit of Start

Fan Start PWM

Slope PWM 1

PWM Manual mode

The fan spins at the speed set in:

Fan

PWM

control

Temp. Limit of OFF [000]

WARNING:

CPU failure can result if this value is set too high

The fan will turn off if the temperature falls below this value.

Minimum Value: 0°C

Maximum Value: 127°C

Temp. Limit of Start [020]

WARNING:

CPU failure can result if this value is set too high

When the fan is off, it will only start when the temperature exceeds this setting.

Minimum Value: 0°C

Maximum Value: 127°C

Start PWM [070]

This is the initial speed of the fan when it first starts spinning.

PWM Minimum Mode: 0

Summary of Contents for ISP-9652/9602
























































































































Search results

Summary of Contents for ISP-9652/9602

Reviews:

Related manuals for ISP-9652/9602

Brands by name

Popular brands

IEI Technology ISP-9652/9602, User Manual

Search results

Summary of Contents for ISP-9652/9602

Reviews:

Related manuals for ISP-9652/9602

Brands by name

Popular brands