manualshive.com logo in svg

IEI Technology ISP-9652/9602, User Manual

Share
Download
IEI Technology ISP-9652/9602 User Manual Download Page 63

 

 

ISP-9652/9602 User Manual 

Page 51

Step 4: 

Attach the bracket to the chassis

. The USB 2.0 connectors are attached to a 

bracket. To secure the bracket to the chassis please refer to the installation 

instructions that came with the chassis.

Step 0:

 

4.7.5 VGA Monitor Connection 

The ISP-9652/9602 has a single onboard female DB-15 connector. The DB-15 connector 

is connected to a CRT or VGA monitor. To connect a monitor to the ISP-9652/9602, 

please follow the instructions below. 

Step 1: 

Locate the female DB-15 connector

. The location of the female DB-15 

connector is shown in 

Chapter 3

. 

Step 2: 

Align the VGA connector

. Align the male DB-15 connector on the VGA screen 

cable with the female DB-15 connector. 

Step 3: 

Insert the VGA connector

. Once the connectors are properly aligned with the 

insert the male connector from the VGA screen into the female connector on the 

ISP-9652/9602. See 

4

Figure 4-14

. 

 

Figure 4-14: VGA Connector 

Summary of Contents for ISP-9652/9602
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands